• Kawasaki Ninja 2000 Psi Pressure Washer User Manual Free
• Kawasaki Ninja 2000 Psi Pressure Washer User Manual Download
• Kawasaki Ninja 2000 Psi Pressure Washer User Manual Pdf
• Kawasaki Ninja 2000 Psi Pressure Washer User Manual
• Kawasaki Ninja 2000 Psi Pressure Washer User Manual -

This guide will show you exactly how to troubleshoot pressure washer problems.

Including:

• Low water pressure
• Water leaking issues
• Engine/motor turning off while in use
• And much more…

Get quick and easy access to information specific to your Kawasaki vehicle. Download official owner's manuals and order service manuals for Kawasaki vehicles. Dec 15, 2014 Kawasaki High Pressure Water Jet washer can strongly wash objects by jetting pressurized water from nozzles. As jet streams are parallel without diffusing, high energy density washing is obtained. PRESSURE WASHER MANUALS: How to Access Old Pressure Washer Manuals.

• Pressure washer does not turn on. When the power washer does not turn on, it is either due to no water flow or no electricity going to the power washer. In other words, either a water flow or an electrical problem. Water-flow Issue. The first area to check with the customer is water flow.
• Garden product manuals and free pdf instructions. Find the user manual you need for your lawn and garden product and more at ManualsOnline.
• Verify that only the pressure washer is running on this circuit. System has residual pressure. Turn the device OFF, pull the trigger on the spray gun to release pressure, and then turn the device back ON. Voltage loss due to the extension cord. Unplug any extension cords attached and plug the unit directly into the outlet.

But first let me ask you a question:

You ever helped a neighbour fix something?

Be careful because once you do – and word gets around – you’ll be the go-to-fixit-guy-or-gal for everyone and everything.

Trust me, I know. All my neighbours now know me as the power equipment and best pressure washer troubleshooting and tune-up guy.

Here’s what happens when you’re the neighbourhood fixer:

4 pm last Saturday I’m in the shed changing pressure washer water pump oil, and over the fence my neighbour says:

“Hey, James, come fix my pressure washer and I’ll give you a beer.”

5 minutes later (beer in hand) he tells me he bought a used pressure washer with water pressure problems…

…It was an electric and started-up fine but when in-use pulsed out water to start, then after 10 seconds fell to low pressure.

My pressure washer troubleshooting experience told me it was air in the pump causing the problem. We switched off the electric motor but kept the water running through the pump. After holding the trigger to keep the water running through the machine we managed to clear the air from the pump and lines. My neighbour turned the machine on again and it worked. Full pressure, no pulsing.

Why you’ll love this beginner’s guide:

Nothing is worse than a pressure washer that starts up but won’t pressure wash properly. You get excited hearing it roar to speed but then it doesn’t properly clean your surface.

That’s why we put together this in-depth power washer troubleshooting guide for you… So you can fix the problem from your garage – even with zero experience and minimal tools.

Jump to each section:

Gas and Electric Pressure Washer Troubleshooting Tips for 20 of the Most Common Pressure Washer Problems

There are 20 pressure washer issues that are by far the most common.

Here’s how we know what they are:

• Reading 300+ emails from pressure washer users asking for help to solve their machine’s issues and counting the occurrences of each fault in an Excel spreadsheet.
• Going through 16 popular pressure washer brands’Operating Manual and tabulating the troubleshooting sections’ listed problems and solutions.
• Looking through my power washer logbooks over the last 8 years to see the most common issues.

After spending 14+ hours gathering the data the common faults could easily be broken down into 5 sections: Water pressure problems, water leaking issues, gas machine specific problems, electric pressure washer faults and other common problems. From there the troubleshooting tips are broken down to 3 columns: What’s wrong, most likely cause and how to fix.

Quick note:

• Always check your Operator’s Manual for troubleshooting tips and safety first. Be aware many of the problems have 5 or more possible solutions for you to try.

Summary Table of Troubleshooting Tips:

The goal of this entire page is to make the most useful pressure washer troubleshooting guide on the internet. We constantly update and improve this table. It was last updated July 11, 2020.

Instructions How To Correct The Tricky Issues

In this section are instructions how to fix the tricky pressure washer issues, namely the ones that require you to tear down the pump.

The Lazy Man’s Way to Diagnose Water Pressure (No Pressure) Issues

Here’s the 5 step approach to solving 95% of water pressure issues in 10 minutes or less:

1. Check water supply: Open the water supply valve to full to ensure the pump is getting enough flow.
2. Check hose for kinks: I can’t tell you how many times I’ve tested a pressure washer, got everything going, only to pull the trigger have it not reach pressure. I check the inlet for blocks. I check the nozzle. I check the water is on. And after all these things check out and it’s still not working I turn it off to read through the manual to find out what I’m doing wrong. Then, all of sudden, I notice a kink in the hose and realize how much an idiot I was not to notice. I fix the kink start the machine and it all works fine. Don’t make this mistake – always check for kinks.
3. Release air from system: Always connect the garden hose to the power washer first. Then turn the water tap on and pull the trigger gun to release water from the system at the garden hose water pressure before starting the engine or motor. This will release all the pressure from the system and allow the pump to function.
4. Ensure correct nozzle and nozzle not clogged:

   Use a needle to clear the nozzle tip of any debris. Any blocks at the nozzle will cause decreased flow and increased pressure in the systems, possibly triggering the unloader to enter bypass.

5. Still experiencing water pressure problems? Okay, no worries, we’ll need to get the tools out to remove unloader valve and check for issues – see below.

Everything You Need to Know About Removing the Unloader Valve to Check for Issues

Unloader valves allow water to run through the pump when you are not holding down the trigger on the pressure gun. If there was no unloader valve then pressure would build inside the system (when not in use) so when you did pull the trigger it would stall the engine or explode a weak link part – probably the pressure hose o-ring.

Check out where the unloader is located on 3 different pressure washer pumps:

As you can see the unloader is located on the exit side of the pump because it allows the pressurized water to flow back through the pump when it isn’t exiting into the high pressure hose (you’re not pressure washing anything).

Take a look at two different disassembled unloader valve assemblies:

The one on the left is from the Stanleygas pressure washer also shown in the above image on the left. It is a flow actuated unloader.

The unloader on the right is from an AR Blue Clean electric pressure washer. It is a pressure actuated unloader.

Both these assemblies can be taken out of the pump for cleaning and repair, without damaging them.

The Difference Between Flow and Pressure Actuated Unloaders

Kawasaki Ninja 2000 Psi Pressure Washer User Manual Free

• Flow actuated – As the name suggests, these unloader valves respond to water flow stoppage. When there is no flow leaving the nozzle the valve will “open” allowing water to flow back to the pump inlet.
  • Pros: Safer because doesn’t require pressure build up.
  • Cons: More sensitive to system issues like a clogged nozzle, incorrect nozzle orifice size and other flow problems.
• Pressure actuated – Instead of responding to flow, this type of unloader is forced open by an increase in water pressure allowing water to bypass back to pump inlet (this pressure is increase is usually caused by flow stoppage).
  • Pros: Less sensitive to flow issues within the system because it responds only to trapped pressure on the outlet side of the pump.
  • Cons: Less safe because it needs pressure rise to work (could cause failures within system).

Troubleshooting the Unloader Valve

Many pressure problems begin and end at the unloader. A cracked o-ring, dirt caught in the spring or a stuck shaft are the most common issues solved by simply removing the unloader and cleaning/looking for issues.

12 Essential Tools and Accessories

The 12 below tools are the most commonly used to repair pressure washers.

Tools

Using the below tools I’ve fully disassembled (all the way down to removing the gas engine piston seals and crankshaft) and put back together: 3 electric pressure washers and 4 gas power washers. Let’s run through the tools, where they are used and if you should buy a complete tool kit or individual tools (and from what tool brands) for repairing your pressure cleaner.

Hex/Allen Keys

Use hex key to remove pump

These are one of the most used tools troubleshooting pressure cleaners because most pump assemblies are fastened together with hex head screws. They are often called Allen head after the company Allen Manufacturing that started mass producing hex screws and hex wrenches (Allen wrenches/keys) to fasten them in the early 1900s.

There are 3 main advantages to hex head screws:

1. Recessed head to make screw durable and unlikely to damage.
2. Use same hex head on different screw types, sizes and threads (thus only one hex key tool required). These would require several different wrenches if they didn’t have hex head. This is likely the reason behind their common use on bicycles – one hex key pocket-size set can help you disassemble and repair your entire bike (many different screw sizes and types but if they all have hex head you only need your hex keys).
3. Torque wrench can be used to tighten them to exact design specification.

Needle-nose Pliers

Use needle-nose pliers to remove the spark plug wire cover

Needle-nose pliers are very handy because they reach small areas to remove o-rings, seals and valves. I use them often when tearing down a pump to fix water pressure issues. I also use them when putting it back together to seat valves and get o-rings and seals into position.

You’ll be very happy to have a set lying around when trying to sort out your power washer faults.

I had a hard time deciding to put hex keys or needle-nose pliers first because they are both used often.

Screwdrivers

Almost the only tool you need to disassemble electric pressure washers is a screwdriver.

Electric machines’ plastic covers – which hide the pump and motor – are held together with Philips head screws.

Gas machines also use Philips – often to clamp down wires and assemble their frames etc.

In addition, you’ll want some slotted screwdrivers to help wedge/drive out certain parts like pump plunger seals. Torx head screws are also used once you get to the engine block.

Sockets & Ratchet

Use ratchet + sockets to remove pump head

Every tool set needs sockets & ratchet and wrenches despite them doing the same thing.

Why?

Because you can have one ratchet and socket heads for every bolt size in a compact case. The ratchet allows you to remove or tighten bolts without repositioning and deep socket attachments allow reach to tight spots.

However, you also need wrenches, especially the open-end side to get to bolts from the side when the top isn’t in reach.

Wrenches

Wrenches have been in use since the 15th century and are probably the most well-known and owned hand tool.

Many prefer to use a ratchet-socket combination because it is quick (don’t have to reposition tool when tightening or loosening fastener) and it’s easier to store (and carry around) 50+ socket heads instead of 50+ wrenches.

But: When you need to get to screws in tight spots you need a wrench. And pressure washers have some tight spots.

Rubber Mallet or Hammer

Kawasaki Ninja 2000 Psi Pressure Washer User Manual Download

Use a hammer to free stubborn parts

Did you know hammers are the oldest known hand tool?

Yup, hammers with handle attached to hard impacting head have been discovered and dated back 30,000 years. And nearly exact replicas of the modern hammer have been found and dated to around 5,000 BC.

They have been useful to humans for 1000s of years – a pretty cool tool.

While troubleshooting pressure cleaners they are used to free stubborn parts like the pump head valve plate.

Utility Knife

Samsung galaxy note korean shv e160s firmware download. Cutting tools like knives have been in use nearly as long as hammers.

They are great help to troubleshoot faults because they make quick work removing the detergent hose and help wedge under tight fitting components to loosen them. Cutting the soap hose is fine because there’s lots of it and you’ll probably damage it using pliers or other means, anyways.

In addition, you probably own several knives already so no need to go out buying any just to help solve pressure washer issues.

Snips

Use snips instead of knife when needed

I like using snips instead of a knife because it’s more precise and quicker.

My snips are sheet-metal snips and cut through tree branches, hoses, and thick plastic or rubber without issue. So if you burst a pressure washer hose, you could cut it shorter (with snips) and install the fitting instead of buying brand new. We did this all the time at a job I had as a 19 year old using a pressure washer to clean a factory parking lot and truck scale every-single-morning.

Snips are a must-own.

Accessories

There’s no need to go into detail about these accessories. You will 100% want to have silicone grease when you reinstall o-rings, and WD-40, thread tape and grease cleaner will be useful, no doubt.

What’s the Best Tool Set to Get?

Click image to see current price on Amazon for this 170-piece Crescent brand tool set

The single kit that has everything you need to troubleshoot pressure cleaners (except for a rubber mallet) is this 170-piece mechanics tool set by Crescent.

You can see that it has:

• Hex keys
• Pliers
• Ratchet + sockets,
• Screwdrivers
• Wrenches
• Snips built in to the needle-nose pliers, and
• Carry case.

If you don’t already own all these hand tools – and you plan on fixing your power washer on your own – then this is the best tool kit.

Troubleshooting Hot Water Power Washers

Hot water pressure washers can suffer 3 faults:

• No hot water produced
• Too much/weird color smoke out the burner
• No flame from blower.

There’s 15 or so reasons why you may experience these faults and the same number of fixes.

Before we get into the fixes, let’s learn more about the burner components.

How a Pressure Washer Burner Works

A hot water pressure washer has a burner to heat the water. The burner uses diesel or kerosene & air + electricity to generate a fire inside a chamber with water circulating around the exterior in tubes coiled like a snake. Water enters at the bottom and by the time it reaches the top – having circulated through all the coil around the flame – exits at the top as hot water.

The burner adds risk/danger to troubleshooting because of the, well, fire. We recommend you take it to a pressure washer repair centre to get fixed. However, there are some simple fixes.

Anatomy of a hot water pressure washer burner unit

What parts does a pressure washer burner have?

1. Steel tubing/coil
2. Insulation
3. Fuel pump/motor and fuel spray nozzle
4. Blower motor
5. Electrodes/ignition tranformer
6. Thermostat/controller
7. Flow switch
8. Pressure release valve
9. Air adjustment slider
10. Fuel filter
11. Exhaust

Here’s a 9-minute video to explain everything on burner troubleshooting:

Brand Specific Tips & Tricksfor Diagnosing and Fixing Power Washer Issues

Let’s look at popular brands, the types/styles of pressure washer they make (including pump brand & type), common issues with those pumps and where you can find further troubleshooting information.

Troy Bilt Troubleshooting Resources

Troy Bilt sells home-use medium-duty gas powered machines with AR Blue Clean axial cam pumps.

Briggs & Stratton is Troy Bilt’s OEM (original equipment manufacturer) meaning Troy Bilt specifies certain things about the machine (eg. Honda or Briggs engine) and Briggs makes them in their factories. The Troy Bilt sticker is then placed on the power washer for sale.

A common fault is that your Troy Bilt will experience no pressure or low water pressure when you start washing. This is often caused by a dirty or broken unloader valve assembly (see above tips).

Further information: Troy Bilt Support Center

Generac

Generac makes and sells residential-use medium and heavy-duty machines as well as belt driven units for commercial use. They have an OEM overseas to manufacture their pumps and engines then assemble them back in their factories in the USA.

Further information: Generac Pressure Washer Support Product Lookup

Karcher

Karcher makes all types/styles of pressure washers through their own brand and subsidiary brands including Hotsy, Shark and Landa. They are easily the biggest pressure washer maker and seller in the world. They makes models with all types of the best small engines and pumps and have an extensive rental and service network through their subsidiary brands.

Further information: Karcher Pressure Cleaner Knowledgebase

Simpson

Simpson Cleaning sells home and commercial use machines with Kohler, Honda and Simpson OHV engines. The pump brands they use are two in-house brands: OEM Technologies (axial cam) and AAA Pumps (triplex). They also use CAT Pumps brand on some of their premium residential and commercial machines.

Simpson Cleaning are some of the most popular residential gas machines because they offer great value for money and their pressure washers’ wheelbarrow stance is sturdy and much easier to move around compared to the common upright designs.

Common problems include low or no pressure after a few seconds use and soap not entering system properly.

Further information: Simpson Support Page

Now What?

If you pressure wash you’re bound to need to troubleshoot an issue at some stage. Whether it be no water pressure because of a hose kink or low pressure because of a busted o-ring inside the unloader…

…it will happen eventually – but since you made it this far you will have the knowledge to sort your problem out from your garage – with minimal tools and time.

To decrease the risk of having major issues, take a look at the 7 best for home use – these are the best designed and least likely to fail.

Kawasaki Ninja 2000 Psi Pressure Washer User Manual Pdf

Okay, to wrap up: Let’s review the gist of the tips outlined in this guide:

• Water pressure issues (no, low and/or sporadic water pressures): Check water supply is on full and no hose kinks. Check inlet filter isn’t clogged. Check nozzle isn’t blocked. Turn off engine/motor (but keep water on) and pull trigger to release air from system. If none of this works, it may be the unload valve being stuck due to dirt or broken parts. See unloader section above.
• Water leaking from connections: First ensure connections are securely fitted. If water is squirting out while pressure washing it is most likely a busted o-ring inside the the pressure hose. Contact support and get them to send new o-ring or hose.

Be sure to review the summary table above and double the check the brand specific support pages before giving up and returning the machine.

Sources

1. “Troubleshooting Pressure Washer and Power Washer Problems.” www.PressureWasherTroubleShooter.com
2. “Hammer History.” Wikipedia.org
3. “All About Unloader Valves.” www.ePowerWash.com

The Cyclepedia Kawasaki EX500 Ninja 500R online service manual features detailed, full-color photographs and wiring diagrams, complete specifications with step-by-step procedures performed and written by a veteran Kawasaki dealer trained motorcycle technician.

This Cyclepedia manual covers 1987 – 2009 Ninja 500R Kawasaki EX500 motorcycles.

When you subscribe to the Kawasaki EX500 Ninja 500R online motorcycle service manual you’ll get instant access to the following information and more! The photos you see here are just a small sample of what you’ll get in our online shop manual.

Periodic Maintenance for Kawasaki EX500 Ninja 500R – Periodic Maintenance Chart, Clutch Cable Adjustment, Throttle Free Play, Brake Fluid, Engine Idle Speed, Drive Chain Adjustment, Rear Brake Inspection, Brake Pads, Engine Oil, Spark Plugs, Air Filter Servicing, Tires, Valve Clearance, Compression Test

Quick Reference Kawasaki EX500 Ninja 500R – Ninja EX500 Specifications, VIN and Engine Number Location, Torque Specifications, General Torque Specifications

Fuel System Kawasaki EX500 Ninja 500R – Carburetor Removal, Carburetor Installation, Carburetor Assembly, Carburetor Disassembly, Carburetor Synchronization, Carburetor Specifications, Petcock, Airbox, Emissions

External Components Kawasaki EX500 Ninja 500R – Seat, Fuel Tank, Upper Fairings, Lower Fairings, Side Covers, Footpegs, Gearshift Pedal, Handlebar, Front Fender, Rear Fender, Exhaust System

Engine Kawasaki EX500 Ninja – Engine Specifications, Camshaft Removal, Camshaft Installation, Cylinder Head Cover, Cylinder Head, Valves, Cylinders and Pistons, Clutch Removal, Clutch Installation, Engine Removal, Engine Installation, Crankcase Splitting, Crankshaft, Crankcase Assembly, Transmission Removal, Transmission Shafts, Transmission Installation, Gearshift, Alternator

Lubrication System Kawasaki EX500 Ninja – Oil Pan, Oil Pump

Final Drive Kawasaki EX500 Ninja 500R – Drive Chain, Engine Sprocket, Rear Wheel Sprocket

Front Brake Kawasaki EX500 Ninja – Brake Disc, Master Cylinder, Front Brake Caliper, Front Brake Specifications

Rear Brake Kawasaki EX500 Ninja – Master Cylinder, Rear Brake Caliper, Rear Brake Disc, Drum Brake

Wheels Kawasaki EX500 Ninja – Wheel and Axle Inspection, Front Wheel, Rear Wheel, Bearing Replacement

Kawasaki Ninja 2000 Psi Pressure Washer User Manual

Steering Kawasaki EX500 Ninja – Removal, Installation

Front Suspension Kawasaki EX500 Ninja – Fork Removal and Installation, Front Fork Assembly, Front Fork Disassembly

Rear Suspension Kawasaki EX500 Ninja – Rear Suspension Removal, Rear Suspension Installation, Rear Suspension Disassembly, Rear Suspension Assembly

Electrical System Kawasaki EX500 Ninja – Electrical Specifications, Ignition System, Signal Generator, Charging System, Starter System, Switches, Lights, Instrument Panel, Wiring Diagram, Home,

Kawasaki Ninja 2000 Psi Pressure Washer User Manual -

Parts Diagrams

Troubleshooting

Professional Tech Support